View source for 128 x 32 OLED Display

= How to control it in MicroPython = 

The main.py shows the current time on the screen.
<syntaxhighlight lang="python" line='line'>
# main.py displaying the current time
from machine import Pin, SoftI2C
import ssd1306
from time import sleep
import utime

# Initialize I2C interface with the correct pins for your setup
i2c = SoftI2C(scl=Pin(13), sda=Pin(12))

# Initialize SSD1306 OLED display
oled_width = 128
oled_height = 32  # Adjusted for 128x32 OLED display
oled = ssd1306.SSD1306_I2C(oled_width, oled_height, i2c)

while True:
    # Clear the display
    oled.fill(0)
    
    # Get the current time
    current_time = utime.localtime()
    time_str = '{:02}:{:02}:{:02}'.format(current_time[3], current_time[4], current_time[5])
    
    # Display the current time
    oled.text('Current Time:', 0, 0) # first line
    oled.text(time_str, 0, 10) # second line
    #oled.text("EMPTY", 0, 20) #third line
    
    # Update the display
    oled.show()
    
    # Wait for a bit before updating again
    sleep(1)

</syntaxhighlight>


ssd1306.py
<syntaxhighlight lang="python" line='line'>
# ssd1306.py - MicroPython SSD1306 OLED driver, I2C and SPI interfaces

from micropython import const
import framebuf

# register definitions
SET_CONTRAST = const(0x81)
SET_ENTIRE_ON = const(0xa4)
SET_NORM_INV = const(0xa6)
SET_DISP = const(0xae)
SET_MEM_ADDR = const(0x20)
SET_COL_ADDR = const(0x21)
SET_PAGE_ADDR = const(0x22)
SET_DISP_START_LINE = const(0x40)
SET_SEG_REMAP = const(0xa0)
SET_MUX_RATIO = const(0xa8)
SET_COM_OUT_DIR = const(0xc0)
SET_DISP_OFFSET = const(0xd3)
SET_COM_PIN_CFG = const(0xda)
SET_DISP_CLK_DIV = const(0xd5)
SET_PRECHARGE = const(0xd9)
SET_VCOM_DESEL = const(0xdb)
SET_CHARGE_PUMP = const(0x8d)

# Subclassing FrameBuffer provides support to the graphics primitives
class SSD1306(framebuf.FrameBuffer):

    def __init__(self, width, height, external_vcc):
        self.width = width
        self.height = height
        self.external_vcc = external_vcc
        self.pages = self.height // 8
        self.buffer = bytearray(self.pages * self.width)
        super().__init__(self.buffer, self.width, self.height, framebuf.MONO_VLSB)
        self.init_display()

    def init_display(self):
        for cmd in (
            SET_DISP | 0x00,  # display off
            # address setting
            SET_MEM_ADDR, 0x00,  # horizontal
            # resolution and layout
            SET_DISP_START_LINE | 0x00,
            SET_SEG_REMAP | 0x01,  # column addr 127 mapped to SEG0
            SET_MUX_RATIO, self.height - 1,
            SET_COM_OUT_DIR | 0x08,  # scan from COM[N] to COM0
            SET_DISP_OFFSET, 0x00,
            SET_COM_PIN_CFG, 0x02 if self.height == 32 else 0x12,
            # timing and driving scheme
            SET_DISP_CLK_DIV, 0x80,
            SET_PRECHARGE, 0x22 if self.external_vcc else 0xf1,
            SET_VCOM_DESEL, 0x30,  # 0.83*Vcc
            # display
            SET_CONTRAST, 0xff,  # maximum
            SET_ENTIRE_ON,  # output follows RAM contents
            SET_NORM_INV,  # not inverted
            # charge pump
            SET_CHARGE_PUMP, 0x10 if self.external_vcc else 0x14,
            SET_DISP | 0x01):  # display on
            self.write_cmd(cmd)
        self.fill(0)
        self.show()

    def poweroff(self):
        self.write_cmd(SET_DISP | 0x00)

    def poweron(self):
        self.write_cmd(SET_DISP | 0x01)

    def contrast(self, contrast):
        self.write_cmd(SET_CONTRAST)
        self.write_cmd(contrast)

    def invert(self, invert):
        self.write_cmd(SET_NORM_INV | (invert & 1))

    def show(self):
        xpos0 = 0
        xpos1 = self.width - 1
        self.write_cmd(SET_COL_ADDR)
        self.write_cmd(xpos0)
        self.write_cmd(xpos1)
        self.write_cmd(SET_PAGE_ADDR)
        self.write_cmd(0)
        self.write_cmd(self.pages - 1)
        self.write_data(self.buffer)

    def write_cmd(self, cmd):
        raise NotImplementedError

    def write_data(self, buf):
        raise NotImplementedError

class SSD1306_I2C(SSD1306):

    def __init__(self, width, height, i2c, addr=0x3c, external_vcc=False):
        self.i2c = i2c
        self.addr = addr
        self.temp = bytearray(2)
        self.write_list = [b'\x40', None]  # Co=0, D/C#=1
        super().__init__(width, height, external_vcc)

    def write_cmd(self, cmd):
        self.temp[0] = 0x80  # Co=1, D/C#=0
        self.temp[1] = cmd
        self.i2c.writeto(self.addr, self.temp)

    def write_data(self, buf):
        self.write_list[1] = buf
        self.i2c.writevto(self.addr, self.write_list)
</syntaxhighlight>